Ultra electronics VersaMux-4000 Скачать руководство пользователя

Страница: 8 / 180

Document Formats

Preface

Page P-2

VersaMux-4000 Operation & Installation Guide

Part No. 24001157

Revision C

Document Formats

This section briefly describes the use of fonts (type faces), styles, and symbols,
used throughout this document.

Bold Paragraph

Text

Bold text in the document body text represents names and symbols that appear on
the user interface screens. For example:

•

Select

Administration

from the

Main Menu

The

System Administration

screen appears.

In this example “

Administration

” is a parameter on a screen and “

Main Menu

”

and “

System Administration

“ are screen titles that appear on the screens.

Bold Courier Font

Courier font, also referred to as “typewriter font” appears in this document as
something you type into the User Interface. For example:

•

Type the following into the field:

connect1

where “

connect1

” is what you actually type.

Notes

Important information and tips appear as notes. Notes have a special format and
appearance. The following is an example of the Note format:

NOTE:

This is how a note appears in this document.

Warning Formats

This document may use warnings for various potential conditions. The following
are the warning formats with descriptions of their use:

WARNING:

This format is used for an electrical danger that may Injure

or kill the user.

Содержание VersaMux-4000





















































































































































































Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды

Ultra electronics VersaMux-4000, Руководство по эксплуатации и установке

Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды