Ultra electronics VersaMux-4000 Скачать руководство пользователя

Страница: 121 / 180

Chapter 6: Diagnostics

LED Indicators

Part No. 24001157

VersaMux-4000 Operation & Installation Guide

Page 6-5

Revision C

LED States

Table 6-1

provides descriptions of the front panel status LED indicator states.

Table 6-1

Front Panel Indicator State Descriptions

LED Label

State

Description

Power

Green

AC power to the system is present.

Off

The unit is not powered or the

FP-Lighting Parameter

disabled the indicators.

Aggr

Red

At least one fault exists on the aggregate.

Yellow

Aggregate operating in loopback mode.

Green

The aggregate operation is normal with no faults.

Clk Ref

Red

The system lost synchronization with the timing
reference.

Green

The system has synchronization with the timing
reference.

Ports

Green

All ports are in normal operation (no faults, not in
loopback).

Red

At least one fault exists on one or more ports.

Yellow

One or more ports operating in loopback mode.

Fault

Red

One or more system faults exist on the VersaMux-4000.

In addition, this indicator illuminates when the

Hot-swap

parameter is

Enabled

Off

The VersaMux-4000 system operation is normal (no
faults).

Table 6-1

Содержание VersaMux-4000





















































































































































































Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды

Ultra electronics VersaMux-4000, Руководство по эксплуатации и установке

Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды