Ultra electronics VersaMux-4000 Скачать руководство пользователя

Страница: 84 / 180

Configure

Chapter 5: Operating Instructions

Page 5-14

VersaMux-4000 Operation & Installation Guide

Part No. 24001157

Revision C

FP-Lighting Parameter

The

FP-Lighting

parameter specifies the front panel display lighting mode.

Table 5-4

describes the options for the

FP-Lighting

parameter.

Offline

The

Offline

sub-menu allows you to provision a configuration without disturbing

a unit while in operation. When you complete the offline configuration, you can
use the

Activate

parameter to apply the offline configuration to the active

configuration (see

“Activate” on page 5-34

The

Offline

sub-menu contains the following items:

•

Aggregate

(See

“Aggregate” on page 5-16

)

•

Port-1

(see

“Port-1, Port-2, Port-3 or Port-4” on page 5-21

)

•

Port-2

(see

“Port-1, Port-2, Port-3 or Port-4” on page 5-21

)

•

Port-3

(see

“Port-1, Port-2, Port-3 or Port-4” on page 5-21

)

•

Port-4

(see

“Port-1, Port-2, Port-3 or Port-4” on page 5-21

)

•

Copy-Config

(see

“Copy-Config” on page 5-23

)

Table 5-4

FP-Lighting Option Descriptions

Option

Description

Off

Selecting this option disables both the LCD backlighting and the status LEDs.

Selecting this option illuminates the LCD backlighting and the status LEDs.

30-seconds

Selecting this option enables the LCD backlighting and illuminates the status LEDs
during keypad activity. The backlighting and LEDs turns off after 30 seconds of keypad
inactivity.

Table 5-4

Содержание VersaMux-4000





















































































































































































Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды

Ultra electronics VersaMux-4000, Руководство по эксплуатации и установке

Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды