Ultra electronics VersaMux-4000 Скачать руководство пользователя

Страница: 93 / 180

Chapter 5: Operating Instructions

Configure

Part No. 24001157

VersaMux-4000 Operation & Installation Guide

Page 5-23

Revision C

Copy-Config

The

Copy-Config

parameter enables you to copy the values of a configuration.

This is very useful if you want to create a new configuration similar to an existing
one.

Table 5-7

describes the

Copy-Config

parameter options and actions.

Fiber-Timing

NOTE:

This parameter only appears in Software Versions 2.18 (DNE Part Number

25400645-011) and greater.

The

Fiber-Timing

parameter only has an affect when the Mode parameter is set to

Fiber-FOM

This parameter controls the timing reference

of the transmit 23.552

MHz timing when the port is operated in Fiber-FOM mode. The options are:

CTM

- Use this option when the remote equipment is a Codem CTM-100C.

Standard

- Use this option when the remote equipment is a device other than a

Codem CTM-100C (for example, a MD-1272, GSC-54, CV-FOM, CV-HTU-16M, etc.).

Table 5-6

Port Parameter and Option Descriptions

Parameter

Options and Description

Table 5-6

(page 3 of 3)

Table 5-7

Copy-Config Options and Descriptions

Option

Description of Action When Selected

The system will not copy the configuration nor make any changes.

Active

The system copies all of the active configuration parameter values to the offline
configuration.

Undo

When you activate an offline configuration, the system stores the previous
configuration in “undo.” When you select

Undo

the system copies the configuration

stored in undo to the offline configuration.
For example, if you have an original active configuration that you replaced by
activating the offline configuration, you can restore the original configuration by
selecting

Undo

Table 5-7

Содержание VersaMux-4000





















































































































































































Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды

Ultra electronics VersaMux-4000, Руководство по эксплуатации и установке

Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды