Ultra electronics VersaMux-4000 Скачать руководство пользователя | Manualshive

Страница: 91 / 180

background image

Chapter 5: Operating Instructions

Configure

Part No. 24001157

VersaMux-4000 Operation & Installation Guide

Page 5-21

Revision C

Port-1, Port-2, Port-3 or Port-4

Selecting the

Port-

X (X=1,2,3 or 4) parameter displays a list Port parameters for

the selected port and their current values. The port parameters are:

•

Card-Type

(Read-only).

•

Mode

•

Rate

(Note that the

Rate

parameter does not appear when the

VersaMux is in Port Relay Mode)

•

OW-Filter

(appears for the Combination Module Only)

NOTE:

Since a parameter value has an affect on the other parameters, we highly
recommend that you configure the port parameters in the order listed above
(

Mode

then

Rate

then

OW-Filter

).

provides descriptions for the

Port-

X (1, 2, 3 and 4) parameters and

options.

Table 5-6

Port Parameter and Option Descriptions

Parameter

Options and Description

Card-Type

The card type (Fiber/Cu) will be displayed.

NOTE:

Release 1.0 software supports only the Combo module as a user interface.

Mode

The

Mode

parameter specifies the interface type used for the port interface. Values for

the

Mode

parameter are:

Disabled

- This option disables the Port(s) on the Card.

Cu-CDI

- This option sets the Combo Card to use the Copper CDI interface.

Fiber-CV

- This option sets the Combo Card to use the optical port interface operating

“unframed” (CV mode). Use this option when the Port is connected to a CDI or
Manchester encoded (unframed) signal on the optical interface such as a CV-8448 or a
CV-FOM-D/CV-HTU-16M with its

Fiber-Encoding

parameter set to

CV

.

Fiber-FOM

- This option sets the Combo Card to use the optical port interface

operating in a “framed” format compliant with JTC3A-9109C. Use this option when the
Port is connected to a framed signal on the optical interface such as a MD1272/G,
GSC-54, or a CV-FOM-D/CV-HTU-16M with its

Fiber-Encoding

parameter set to

FOM

.

(page 1 of 3)

«
...
89
90
91
92
93
...
»

Содержание VersaMux-4000





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VersaMux-4000

Бренд: National Instruments Страницы: 93

Бренд: Klein Tools Страницы: 12

Бренд: ennoLogic Страницы: 52

JungleMUX SONET 86447

Бренд: GE Страницы: 28

Бренд: GE Страницы: 16

Бренд: GE Страницы: 24

StoreSafe SDVR-10

Бренд: GE Страницы: 73

JungleMUX 86445-31

Бренд: GE Страницы: 95

Бренд: GE Страницы: 83

86498 ETHER-1000 UNIT

Бренд: GE Страницы: 174

Бренд: arcutroni Страницы: 58

Бренд: Tenma Страницы: 8

Бренд: Tenma Страницы: 10

Бренд: Extech Instruments Страницы: 6

Бренд: Extech Instruments Страницы: 12

Бренд: Extech Instruments Страницы: 19

Бренд: TECPEL Страницы: 7

Бренд: TECPEL Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды