Ultra electronics VersaMux-4000 Скачать руководство пользователя | Manualshive

Страница: 54 / 180

background image

Power-Up and Basic Navigation

Chapter 4: Getting Started

Page 4-4

VersaMux-4000 Operation & Installation Guide

Part No. 24001157

Revision C

Basic Front Panel Navigation

The LCD display has two lines with up to 16-characters on each line. The system
displays Main Menu selections on the top line of the display with the bottom line
left blank.

You can use the right and left arrow keys to navigate through the Main Menu
selections. The system wraps around when you reach the end of the menu.

shows the Main Menu and its navigation.

Figure 4-3

Main Menu, Front Panel Display

Pressing the down arrow key at a menu selection displays its sub-menu selections
or parameters. The system displays the currently configured option for each
parameter on the second line of the display as shown in

. In this

example the option is informational (read-only) so the option is “right justified” on
the display.

Figure 4-4

Informational Item (read-only option) Right Justified on the Display

If you can edit the option (read-write) it appears left justified and an asterisk
appears in the top right corner of the display as shown in

Figure 4-5

Editable Option Left Justified with Asterisk

Pressing the right arrow key with a read-only or read-write option displayed
returns the system to the previous menu selection. This enables you to quickly
exit a long list of parameters or options. Note that pressing the right arrow key
does not return to the menu selection when you are in the edit mode.

To enter the edit mode, press the Enter key when a read-write option appears on
the display. The asterisk disappears indicating that the system is in the edit mode.
When in the edit mode, the left and right arrow keys navigate through the options
for the parameter. To select an option, press the Enter key. The asterisk reappears
and pressing the right arrow key returns you to the menu selection.

Alarm-Status

Configure

Activate

System-Info

Statistics

Diagnostics

Card-Type

NRZ-Card

POWER

AGGR

CLK R

Function *
4-Port-Mux

POWER

AGGR

CLK R

«
...
52
53
54
55
56
...
»

Содержание VersaMux-4000





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VersaMux-4000

Бренд: C-LOGIC Страницы: 4

Seatalk QK-A033

Бренд: Quark-Elec Страницы: 2

Бренд: Quark-Elec Страницы: 2

Бренд: Cronyx Страницы: 48

Бренд: KNOVA Страницы: 32

Бренд: Draper Страницы: 16

MultiMeter-Home

Бренд: LaserLiner Страницы: 68

Бренд: UNI-T Страницы: 36

Бренд: Amprobe Страницы: 89

Бренд: twintex Страницы: 21

Бренд: Pico Macom Страницы: 2

Бренд: Pro's Kit Страницы: 24

Бренд: Major tech Страницы: 16

Бренд: TC Communications Страницы: 18

Бренд: Patton electronics Страницы: 9

Бренд: Fluke Страницы: 120

Бренд: Eaton Страницы: 36

Бренд: Sealey Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды