Ultra electronics VersaMux-4000 Скачать руководство пользователя

Страница: 133 / 180

Chapter 6: Diagnostics

Diagnostics Menu

Part No. 24001157

VersaMux-4000 Operation & Installation Guide

Page 6-17

Revision C

Test

On power-up, the VersaMux-4000 performs a series of Power-On Self Tests (POST)
as described in

Table 6-3

. In addition, you can run additional test by selecting

Test

from the

Diagnostics

menu. This accesses a sub-menu with the following items:

•

Test-Status

- Selecting this parameter provides you with the

following information about the current test:

•

Test-State (Active or Idle)

•

Test-Mode

•

Tests-Performed

•

Tests-Passed

•

Tests-Failed

•

Test-Results

- Selecting this parameter accesses a sub-menu with the

following options:

•

Errors-Only –

Selecting this option displays a list of the failed

test(s) from the most recent “Start-Test.”

•

All-Results –

Selecting this option displays a list of every test

result from the most recent “Start-Test.”.

•

Start-Test

- Selecting this parameter displays the following sub-menu

(note that you need to confirm the Start-Test selection in the terminal
interface to enter the sub-menu selection mode):

•

- Selecting this option exits the Start-Test option without

initiating any tests.

•

BIST

- Selecting this option commands the VersaMux-4000 to run

the Built-In Self Tests as described in

Table 6-3

•

Factory

- Selecting this option runs an extensive series of tests

but produces no end-user information. This option is intended for
DNE factory and field service specialists only.

•

Stop-Test

- Selecting this parameter accesses the following sub-menu

(note that you need to confirm the Stop-Test selection in the terminal
interface to enter the sub-menu selection mode):

•

- Selecting this option exits the stop-test selection mode and

allows the current test to continue uninterrupted.

•

Yes

- Selecting this option terminates the current test.

Содержание VersaMux-4000





















































































































































































Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды

Ultra electronics VersaMux-4000, Руководство по эксплуатации и установке

Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды