Ultra electronics VersaMux-4000 Скачать руководство пользователя | Manualshive

Страница: 2 / 180

background image

Trademarks

All brand or product names are trademarks or registered trademarks of their respective companies or
organizations.

Copyright

©2007 Ultra Electronics, DNE Technologies. ALL RIGHTS RESERVED.

No part of this document may be copied, photocopied, reproduced, translated or reduced to any electronic
or machine-readable format without prior written permission of Ultra Electronics, DNE Technologies.

This document, and the technical data within, is controlled for export by the United States Department of
State. It, or any part thereof, may not be exported or transferred to any foreign person either in the United
States or abroad, or disclosed to a national of another country without the prior written approval of the
United States Department of State.

The information in this document is subject to change without notice. Ultra Electronics, DNE Technologies
assumes no responsibility for any damages arising from the use of this document, including but not limited
to, lost revenue, lost data, claims by third parties, or other damages.

Revision History

Revision

Date

Description

A

7/2006

First Issue

B

3/2007

Revised for Software Version 2.18. Added Fiber-Timing parameter to

Table 5-6 on page 5-21

. Added note about Sync-Inhibit parameter

Table 5-5 on page 5-17

C

12/2007

Added parameter configuration notes to

“Aggregate” on page 5-16

and

“Port-1, Port-2, Port-3 or Port-4” on page 5-21

.

«
1
2
3
4
...
»

Содержание VersaMux-4000





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VersaMux-4000

Бренд: Cronyx Страницы: 48

Бренд: Extech Instruments Страницы: 19

Бренд: Greenlee Страницы: 56

Бренд: Sanwa Страницы: 14

Бренд: Sanwa Страницы: 31

Бренд: Sanwa Страницы: 56

Бренд: Di-LOG Страницы: 36

Бренд: F&F Страницы: 16

Бренд: Conrad Страницы: 34

Бренд: UNI-T Страницы: 64

Бренд: UNI-T Страницы: 73

Бренд: DAIICHI Страницы: 72

Бренд: Major tech Страницы: 14

Бренд: TDE Instruments Страницы: 16

Бренд: Keithley Страницы: 61

Бренд: GearLite Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Delton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды