Ultra electronics VersaMux-4000 Скачать руководство пользователя

Страница: 75 / 180

Chapter 5: Operating Instructions

Alarm-Status

Part No. 24001157

VersaMux-4000 Operation & Installation Guide

Page 5-5

Revision C

Alarm-Status

Selecting the

Alarm-Status

parameter from the Main Menu displays a list of the

active alarms.

Table 5-1

provides a list of the alarms their descriptions, and the interfaces they

apply to.

Table 5-1

Alarm Descriptions

Alarm

Description

System

Port

-1

Port

-2

Port

-3

Port

-4

Aggrega

POST-Fail

One or more of the Power-On-Self-Tests failed.

BIST-Fail

One or more of the Built-In-Self-Tests failed one or more.

FTM-Fail

One or more of the Factory-Test-Mode tests failed.

Stack-Low

The Operating-System-Stack is low.

Hot-Swap

The Hot-Swap mode is enabled.

Incompat-HW

The interface card in this slot is incompatible with the
configured mode.

RefClk_Fail

The Reference-Clock has failed. This failure could be
caused by; no signal present, poor signal present,
reference signal at the wrong rate.

SystFPGA

The System FPGA is not programmed.

TxAggrFPGA

The Tx-Aggregate FPGA is not programmed.

RxAggrFPGA

The Rx-Aggregate FPGA is not programmed.

Insuff-BW

The sum of the individual port bandwidths exceeds the
available aggregate bandwidth.

LOF

The aggregate is in a Loss-Of-Frame condition.

PLL-Lock

The interface card PLL is not locked to the reference.

Sync-Loss

The interface card receiver is not in sync.

BERT-Active

The active BERT is affecting port or aggregate user traffic.

FIFO-Err

The interface card FIFO has overflowed or has an under-
run condition.

Table 5-1

Содержание VersaMux-4000





















































































































































































Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды

Ultra electronics VersaMux-4000, Руководство по эксплуатации и установке

Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды