Trane Tracer AH540 Скачать руководство пользователя страница 63

Страница: 63 / 96

CNT-SVX05A-EN

Configuration

Table 34 — Analog inputs

Note 1:

Trane’s Rover service tool uses the unit type to determine and download the proper default analog input

configuration.

Table 35 — Binary inputs

Note 1:

Trane’s Rover service tool uses the unit type to determine and download the proper default binary input

configuration.

Note 2:

When the supply fan is off, the state of the fan status device is its normal state. For example, if the fan status

switch (end device) is normally open when the fan is off, the controller should be configured for a normally open fan
status input.

Note 3:

When the supply fan is off, the state of the filter status device is its normal state. For example, if the filter status

switch (end device) is normally closed when the fan is off, the controller should be configured for a normally closed
filter status input.

Table 36 — Outdoor air damper

Note 1:

Occupied standby minimum damper position only applies to space temperature control operation.

Note 2:

This is the outdoor air temperature below which the outdoor air damper will always be closed.

Note 3:

Adjustable open time for the outdoor air damper to open from 0% to minimum position.

Table 37 — Exhaust fan or damper

Note 1:

The exhaust fan is energized when the outdoor air damper is equal to or greater than the exhaust fan start

setpoint. The exhaust fan is turned off when the outdoor air damper is less than the exhaust fan start setpoint minus
the exhaust fan stop differential.

Analog input
(Note 1)

Function

Calibration range

Default value

IN 1

Space temperature sensor

+/-10.0

F (+/-5.7°C)

(0.1

F resolution)

IN 2

Hardwired setpoint

+/-10.0

F (+/-5.7°C)

(0.1

F resolution)

IN 3

Fan mode switch

IN 4

Discharge air temp

IN 5

Outdoor air temp

IN 6

Mixed air temp

Duct static

Duct static pressure

Binary input
(Note 1)

Function

Valid range

Default Configuration

IN 7

Low temp detect or
Not used

Normally open or
Normally closed

Dependent on air handling
unit type

IN 8

Run/stop or
Not used

Normally open or
Normally closed

Run/stop
Normally open

IN 9

Occupancy,
generic or Not used

Normally open or
Normally closed

Occupancy
Normally open

IN 10

Supply fan status or
Not used

Normally open (Note 2) or
Normally closed (Note 2)

Sales order dependent

IN 11

Filter status or
Not used

Normally open (Note 3) or
Normally closed (Note 3)

Sales order dependent

IN 12

Exhaust fan status or
Not used

Normally open or
Normally closed

Sales order dependent

Parameter

Valid range

Default value

Occupied outdoor damper minimum position

0 to 100%

15%

Occupied standby damper minimum position (Note 1)

0 to 100%

Economizer enable temperature (dry bulb)

32°F to 122°F
(0°C to 50°C)

F (15.6

Low ambient damper lock out temperature (Note 2)

-40 to 32

(-40°C to 0°C)

-20

F (-28.9

Outdoor air damper open time (Note 3)

0 to 30 minutes

5 minutes

Parameter

Valid range

Default value

Exhaust fan start setpoint (Note 1)

0 to 100%

26%

Exhaust fan stop differential (Note 1)

0 to 100%

10%

Содержание Tracer AH540

































































































Результаты поиска

Содержание Tracer AH540

Отзывы:

Похожие инструкции для Tracer AH540

Бренды по названию

Популярные бренды

Trane Tracer AH540, Руководство по диагностике для владельца установки

Результаты поиска

Содержание Tracer AH540

Отзывы:

Похожие инструкции для Tracer AH540

Бренды по названию

Популярные бренды