Trane Tracer AH540 Скачать руководство пользователя страница 64

Страница: 64 / 96

CNT-SVX05A-EN

Configuration

Table 38 — Local zone sensor fan switch

Table 39 — Space temperature setpoints

Note 1:

The heating and cooling setpoint high and low limits only apply to the occupied and occupied standby setpoints

and are never applied to the unoccupied setpoints.

Table 40 — Discharge air setpoint limits for constant volume space
temperature control

Note 1:

When the Tracer AH.540 controller is configured for constant volume space temperature control (control mode),

the control algorithm is limited to calculating this high and low discharge air temperature setpoint.

Table 41 — Discharge air temperature control setpoints and setpoint limits

Table 42 — Daytime warm-up

Note 1:

When the space temperature is below the daytime warm-up start setpoint, the daytime warm-up sequence is

initiated.

Note 2:

When the space temperature is above the daytime warm-up stop setpoint, the daytime warm-up sequence is

terminated.

Parameter

Valid range

Default

Local fan switch

Enable or disable

Enable

Default setpoint

Valid range

Default value

Occupied heating setpoint

40 to 115

F (4.44 to 46.1°C)

F (21.7

Occupied cooling setpoint

40 to 115

F (4.44 to 46.1°C)

F (23.3

Occupied standby heating setpoint

40 to 115

F (4.44 to 46.1°C)

F (19.4

Occupied standby cooling setpoint

40 to 115

F (4.44 to 46.1°C)

F (25.6

Unoccupied heating setpoint

40 to 115

F (4.44 to 46.1°C)

F (15.6

Unoccupied cooling setpoint

40 to 115

F (4.44 to 46.1°C)

F (29.4

Heating setpoint low limit (Note 1)

40 to 115

F (4.44 to 46.1°C)

F (4.4

Cooling setpoint low limit (Note 1)

40 to 115

F (4.44 to 46.1°C)

F (4.4

Heating setpoint high limit (Note 1)

40 to 115

F (4.44 to 46.1°C)

104

F (40

Cooling setpoint high limit (Note 1)

40 to 115

F (4.44 to 46.1°C)

104

F (40

Thumbwheel setpoint

Disable or enable

Enable

Limit

Valid range

Default value

Disharge temperature setpoint high limit (Note 1)

38 to 150

(3.3 to 65.6

104

F (40

Disharge temperature setpoint low limit (Note 1)

35 to 150

(1.7 to 65.6

F (7.2

Setpoint

Valid range

Default value

Discharge air cooling setpoint

32°F to 86°F
(0°C to 30°C)

F (12.8

Discharge air heating setpoint

50 to 158°F
(10°C to 70°C)

100

F (37.8

Maximum discharge air cooling setpoint

32°F to 86°F
(0°C to 30°C)

F (20

Minimum discharge air cooling setpoint

32°F to 86°F
(0°C to 30°C)

44.6

F (7

Maximum discharge air heating setpoint

32°F to 158°F
(0°C to 70°C)

104

F (40

Minimum discharge air heating setpoint

32°F to 158°F
(0°C to 70°C)

F (30

Parameter

Valid range

Default value

Daytime warm-up start setpoint (Note 1)

40 to 87.0

(4.4 to 30.6

F (16.7

Daytime warm-up stop setpoint (Note 2)

43 to 90

(6.1 to 32.2

F (21.7

Содержание Tracer AH540

































































































Результаты поиска

Содержание Tracer AH540

Отзывы:

Похожие инструкции для Tracer AH540

Бренды по названию

Популярные бренды

Trane Tracer AH540, Руководство по диагностике для владельца установки

Результаты поиска

Содержание Tracer AH540

Отзывы:

Похожие инструкции для Tracer AH540

Бренды по названию

Популярные бренды