Trakka Corp Trakkabeam A800 Скачать руководство пользователя страница 59

Страница: 59 / 132

COMPONENT MAINTENANCE MANUAL

Publication No. 051019-1 Rev H

DOCUMENT UNCONTROLLED WHEN PRINTED

Page 59

33-46-00

AS9100 Certified

23-Mar-2015

Rev B

J. Setting the STOW and DEPLOY Positions

NOTE: In azimuth, the slow speed zone begins at 18° from the soft stop positions.

Refer to Chapter 4, K.

NOTE: In elevation, the slow speed zone begins 18° from the soft stop positions.

Refer to Chapter 4, K.

(1) The STOW and DEPLOY positions are defined and set by the operator. The settings can be

changed within the azimuth and elevation range of movement as required.

(2) In this example the STOW position is to be set to 0° azimuth and -15° elevation while the DEPLOY

position is to be set to -30° azimuth and -40° elevation.

(3) To program the STOW position:

(a) Drive the searchlight to the required STOW position.
(b) Set the STOW position with a “long press” (> 3 seconds) of the STOW switch on the grip

hand controller or hold the filter switch in the ENT position and press the STOW button on the

TCP.

NOTE: Setting of the STOW position is not possible in flight. The system has a

‘weight-on-wheels’ interlock sensor which prevents this operation until the

aircraft is on the ground.

switch once.

(d) The searchlight will return to the STOW position.

NOTE: If the searchlight does not move, the STOW position has not been correctly

set and the process must be repeated.

(4) To program the DEPLOY position:

(a) Drive the searchlight to the required DEPLOY position.
(b) Set the DEPLOY position with a “long press” (> 3 seconds) of the DEPLOY switch on the grip

hand controller or hold the filter switch in the ENT position and press the DEPLOY button on

the TCP.

switch once.

(d) The searchlight will return to the DEPLOY position.

NOTE: If the searchlight does not move, the DEPLOY position has not been

correctly set and the process must be repeated.

AIRBUS HELICOPTERS: CMM L334M6304E01 ISSUE: B PAGE 77 OF 165

The document reference is online, please check the correspondence between the online documentation and the printed version.

Содержание Trakkabeam A800





































































































































Результаты поиска

Содержание Trakkabeam A800

Отзывы:

Бренды по названию

Популярные бренды

Trakka Corp Trakkabeam A800, Руководство по техническому обслуживанию компонентов

Результаты поиска

Содержание Trakkabeam A800

Отзывы:

Бренды по названию

Популярные бренды