TP-Link L-R480T+ Скачать руководство пользователя

Страница: 66 / 131

-60-

H.323 ALG:

Enable or disable H.323 ALG. The default setting is enabled.

H.323 is used for various applications such as NetMeeting and

VoIP.

SIP ALG:

Enable or disable SIP ALG. The default setting is enabled. It is

recommended to keep the default setting if no special

requirement.

IPsec ALG:

Enable or disable IPsec ALG. The default setting is enabled. It is

recommended to keep default if no special requirement.

PPTP ALG:

Enable or disable PPTP ALG. The default setting is enabled. It is

recommended to keep default if no special requirement.

4.5.2 Traffic Control

Traffic Control functions to control the bandwidth by configuring rules for limiting various data flows. In

this way, the network bandwidth can be reasonably distributed and utilized.

4.5.2.1

Setup

Choose the menu

Advanced

→

Traffic Control

→

Setup

to load the following page.

Figure 4-30 Configuration

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды