TP-Link L-R480T+ Скачать руководство пользователя

Страница: 49 / 131

-43-

Normal:

Displays the number of the received packets (including error frames) that

are between 64 bytes and the maximum frame length. The maximum

untagged frame this router can support is 1518 bytes long and the

maximum tagged frame is 1522 bytes long.

Oversize:

Displays the number of the received packets (including error frames) that

are longer than the maximum frame

Total (Bytes):

Displays the total number of the received or transmitted packets

(including error frames).

Check the box and click the <Clear> button to clear the traffic statistics of the corresponding port.

Click the <Clear All> button to clear all the traffic statistics.

4.3.5.2

Port Mirror

Port Mirror, the packets obtaining technology, functions to forward copies of packets from one/multiple

ports (mirrored port) to a specific port (mirroring port). Usually, the mirroring port is connected to a data

diagnose device, which is used to analyze the mirrored packets for monitoring and troubleshooting the

network.

Choose the menu

Network

→

Switch

→

Port Mirror

to load the following page.

Figure 4-16 Port Mirror

The following items are displayed on this screen:



General

Enable Port Mirror:

Check the box to enable the Port Mirror function. If unchecked, it will be

disabled.

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды