TP-Link L-R480T+ Скачать руководство пользователя

Страница: 26 / 131

-20-

Default Gateway:

Optional. Enter the Gateway assigned by your ISP.

MTU:

MTU (Maximum Transmission Unit) is the maximum data unit

transmitted by the physical network. It can be set in the range of

576-1500. The default MTU is 1500. You are recommended to keep

the default value if no other MTU value is provided by your ISP.

Primary DNS:

Enter the IP address of your ISP’s Primary DNS (Domain Name

Server). If you are not clear, please consult your ISP. It is not

allowed to access the Internet via domain name if the Primary DNS

field is blank.

Secondary DNS:

Optional. If a Secondary DNS Server address is available, enter it.

Upstream Bandwidth:

Specify the bandwidth for transmitting packets on the port.

Downstream

Bandwidth:

Specify the bandwidth for receiving packets on the port.

2) Dynamic

If your ISP (Internet Service Provider) assigns the IP address automatically, please choose the

Dynamic IP connection type to obtain the parameters for WAN port automatically.

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды