TP-Link L-R480T+ Скачать руководство пользователя

Страница: 52 / 131

-46-

The following items are displayed on this screen:



Rate Control

Port:

Displays the port number.

Ingress Limit:

Specify whether to enable the Ingress Limit feature.

Ingress Rate:

Specify the limit rate for the ingress packets.

Egress Limit:

Specify whether to enable Egress Limit feature.

Egress Rate:

Specify the limit rate for the egress packets.

The first entry in Figure 4-17 indicates: The Ingress and Egress Limits are enabled for port 1. The

Ingress and Egress Rates are 1Mbps. That is, the receiving rate for all the ingress packets will not

exceed 1Mbps, and the transmitting rate for all the egress packets will not exceed 1Mbps.

4.3.5.4

Port Config

On this page, you can configure the basic parameters for the ports.

Choose the menu

Network

→

Switch

→

Port Config

to load the following page.

Figure 4-18 Port Config

The following items are displayed on this screen:



Port Config

Status:

Specify whether to enable the port. The packets can be transported via

this port after being enabled.

Flow Control:

Allows you to enable/disable the Flow Control function.

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды