TP-Link L-R480T+ Скачать руководство пользователя

Страница: 69 / 131

-63-

Guaranteed

Bandwidth (Down):

Specify the Guaranteed Downstream Bandwidth for this entry.

Limited Bandwidth

(Down):

Specify the Limited Downstream Bandwidth for this entry.

Effective Time:

Specify the time for the entry to take effect.

Description:

Give a description for the entry.

Status:

Activate or inactivate the entry.



List of Rules

You can view the information of the entries and edit them by the Action buttons.

The first entry in Figure 4-31 indicates: The users within group “sales” share the bandwidth and

the Downstream/Upstream Guaranteed Bandwidth is 5000kbps, while the Downstream/Upstream

Limited bandwidth is 10000kbps.

This entry takes effect at 8 a.m. to 10 p.m. from Monday to

Friday.

Note:

●

The premise for single rule taking effect is that the bandwidth of the interface for this rule is

sufficient and not used up.

●

It is impossible to satisfy all the guaranteed bandwidth if the total guaranteed bandwidth specified

by all Bandwidth Control rules for certain interface exceeds the physical bandwidth of this

interface.

4.5.3 Session Limit

The amount of TCP and UDP sessions supported by the router is finite. If there are some local hosts

transmitting too many TCP and UDP sessions to the public network, the communication quality of the

other local hosts will be affected, thus it is necessary to limit the sessions of those hosts.

4.5.3.1

Session Limit

On this page, you can configure the session limit to specified PCs.

Choose the menu

Advanced

→

Session Limit

→

Session Limit

to load the following page.

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды