TP-Link L-R480T+ Скачать руководство пользователя

Страница: 35 / 131

-29-

IP Address:

If Static IP is selected, configure the IP address of WAN port.

If Dynamic IP is selected, the IP address of WAN port

obtained is displayed.

Subnet Mask:

If Static IP is selected, configure the subnet mask of WAN

port. If Dynamic IP is select, the subnet mask of WAN port

obtained is displayed.

Default Gateway:

If Static IP is selected, configure the default gateway. If

Dynamic IP is selected, the obtained default gateway is

displayed.

Primary DNS/Secondary DNS:

If Static IP is selected, configure the DNS. If Dynamic IP is

selected, the obtained DNS is displayed.

Upstream

Bandwidth:

Specify the bandwidth for transmitting packets on the port.

Downstream Bandwidth:

Specify the bandwidth for receiving packets on the port.



L2TP Status

Status:

Displays the status of L2TP connection.



“Disabled” indicates that the L2TP connection type is

not applied.



“Connecting” indicates that the router is obtaining the IP

parameters from your ISP.



“Connected” indicates that the router has successfully

obtained the IP parameters from your ISP.



“Disconnected” indicates that the connection has been

manually terminated or the router gets no response from

your ISP. Please ensure that your settings are correct

and your network is connected well. Consult your ISP if

this problem remains.

IP Address:

Displays the IP address assigned by your ISP.

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды