TP-Link L-R480T+ Скачать руководство пользователя страница 42

Страница: 42 / 131

-36-

The following items are displayed on this screen:



LAN

IP Address:

Enter the LAN IP address of the router. 192.168.0.1 is

the default IP address. The Hosts in LAN can access

the router via this IP address. It can be changed

according to your network.

Subnet Mask:

Enter the Subnet Mask. The default subnet mask is

255.255.255.0.

Note:

If the LAN IP address is changed, you must use the new IP address to login to the router. To guarantee

a normal communication, please be sure that the Gateway address and the Subnet Mask of the Hosts

are consistent with that of the router accordingly.

4.3.2.2

DHCP

The router with its DHCP (Dynamic Host Configuration Protocol) server enabled can automatically

assign an IP address to the computers in the LAN.

Choose the menu

Network

→

LAN

→

DHCP

to load the following page.

Figure 4-10 DHCP Settings

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды