TP-Link L-R480T+ Скачать руководство пользователя

Страница: 67 / 131

-61-

The following items are displayed on this screen:



General

Disable Bandwidth

Control:

Select this option to disable Bandwidth Control.

Enable Bandwidth

Control all the time:

Select this option to enable Bandwidth Control all the time.

Enable Bandwidth

Control When:

With this option selected, the Bandwidth Control will take effect when the

bandwidth usage reaches the specified value.



Default Limit

Limited Bandwidth:

Default Limit applies only for users that are not constrained by

Bandwidth Control Rules. These users share certain bandwidth with

upper limit configured here. Value 0 means all the remained bandwidth

is available to use.



Interface Bandwidth

Interface:

Displays the current enabled WAN port(s). The Total bandwidth is equal to

the sum of bandwidth of the enabled WAN ports.

Upstream

Bandwidth:

Displays the bandwidth of each WAN port for transmitting data. The

Upstream Bandwidth of WAN port can be configured on

WAN

page.

Downstream

Bandwidth:

Displays the bandwidth of each WAN port for receiving data. The

Downstream Bandwidth of WAN port can be configured on

WAN

page.

Note:

●

The Upstream/Downstream Bandwidth of WAN port you set must not be more than the bandwidth

provided by ISP. Otherwise the Traffic Control will be invalid.

●

If there are data flowing into the router from interface A and out from interface B while the

downstream bandwidth of A is different from the upstream bandwidth of B, then the smaller one

should be considered as the effective bandwidth, and vise versa.

●

Click the <View IP Traffic Statistics> button to jump to IP Traffic Statistics page.

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды