TP-Link L-R480T+ Скачать руководство пользователя

Страница: 24 / 131

-18-

4.2 Quick Setup

Please refer to the

Chapter 3 Quick Installation Guide.

4.3 Network

4.3.1 WAN

4.3.1.1

WAN Mode

TL-R480T+ provides four available WAN ports. You can set the number of WAN ports on this page.

Choose the menu

Network

→

WAN

→

WAN Mode

to load the following page.

Figure 4-2 WAN Mode



WAN Mode

WAN Ports:

Select the total number of WAN ports you prefer to use.

And the router will adjust the physical ports accordingly,

which can be illustrated on the following port sketch.

Note:

●

By default, TL-R480T+ is set to work in the mode of dual WAN ports.

●

Any change to the number of WAN ports may lead to a loss of current configurations. Please be

sure to backup your configurations in advance.

4.3.1.2

WAN1

TL-R480T+ provides the following six Internet connection types: Static IP, Dynamic IP, PPPoE/Russian

PPPoE, L2TP/Russian L2TP, PPTP/Russian PPTP and BigPond. To configure the WAN, please first

select the type of Internet connection provided by your ISP (Internet Service Provider).

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды