TP-Link L-R480T+ Скачать руководство пользователя

Страница: 116 / 131

-110-

Figure 4-70 IP Traffic Statistics

The following items are displayed on this screen:



General

Enable IP Traffic
Statistics:

Allows you to enable or disable IP Traffic Statistics.

Enable Auto-refresh:

Allows you to enable/disable refreshing the IP Traffic Statistics
automatically. The default refresh interval is 5 seconds.



Traffic Statistics

Direction:

Select the direction in the drop-down list to get the Flow Statistics of
the specified direction.



IP Traffic Statistics

This table displays the detailed traffic information of corresponding PCs.

Sorted by:

Select the rule for displaying the traffic information.

4.8.5 Diagnostics

4.8.5.1

Diagnostics

This router provides Ping test and Tracert test functions for network diagnose.

Choose the menu

Maintenance

→

Diagnostics

→

Diagnostics

to load the following page.

Содержание L-R480T+




































































































































Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды

TP-Link L-R480T+, Руководство пользователя

Результаты поиска

Содержание L-R480T+

Отзывы:

Похожие инструкции для L-R480T+

Бренды по названию

Популярные бренды