Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 83

Страница: 83 / 283

3.2 Quick Start

3 Diagnostic Programs

Satellite M40/M45 TECRA A4 Dynabook Vx/4 Maintenance

Manual

User can press any key to exit the program.

3.2.8 DMI Write

In addition to reading the DMI information,

DMI Write

also permits attributes editing

and updating: Manufacture, Product Name, Version, Serial Number, UUID and OEM
Part Number, etc. The following screen will be displayed:

In this screen, there are two lines which attribute could be edited and updated. The 1

line (the font in yellow with blue background) shows the attribute’s value that is read
from the current system and the 2

line (the font in red with turquoise background)

shows the same value as that in the 1

line before user’s editing. User can modify the

attribute’s value in the 2

line and press

Enter

to confirm the current edition and

continue editing the next attribute.

During the editing, user could press

to confirm the DMI attribute update or press

to ignore the modification. Press

ESC

to exit the program of DMI Write.

The confirmation screen is as below:

Содержание SATELLITE M40 Series




























































































































































































































































































Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды