manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Поделиться
Скачать
Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 208

4.17 LED board

 

4 Replacement Procedures

 

Satellite M40/M45, TECRA A4, dynabook Vx/4 Maintenance Manual

 

4

-

59

 

4.17

 

I/O Board 

Removing the I/O Board 

Remove the I/O board according to the following procedures and Figure 4-41.  

1.

 

Remove the M2.5x4 black flat-head screw for securing the I/O board. 

2.

 

Remove the I/O board. 

3.

 

Disconnect the SUMI-card (flat cable) from CN3006 on the I/O board. 

 

Figure 4-41 Removing the I/O board 

 

Installing the I/O Board 

Install the sound board according to the following procedures and Figures 4-41.  

1.

 

Connect the SUMI-card to CN3006 on the I/O board. 

2.

 

Place the I/O board in the correct position. 

3.

 

Secure the I/O board with the M2x4 black flat-head screw. 

Содержание SATELLITE M40 Series




























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды