manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Поделиться
Скачать
Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 171

4.2  Wireless LAN Card

 

4  Replacement Procedures

 

Satellite M40/M45, TECRA A4, dynabook V x/4

 

Maintenance Manual

 

4-23

 

4.2  Wireless LAN Card 

Removing the Wireless LAN Card 

Remove the wireless LAN card according to the following procedures and Figures 4-10 and 4-11.  

CAUTION

:  Do not touch the connectors on the wireless LAN card and in the computer 

with bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural 
oils, etc. from your hands. 

1.

 

Turn the computer upside down. 

2.

 

Release the wireless LAN cover securing screw. 

3.

 

Remove the wireless LAN cover. 

4.

 

Disconnect the two antenna cables with the tweezers. 

5.

 

Spread out both the left and right stoppers for fixing the wireless LAN card until the card 
can be raised. 

6.

 

Pull the wireless LAN card up and out at an angle. 

 

Figure 4-10 Removing the wireless LAN card cover 

 

Содержание SATELLITE M40 Series




























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды