Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 175

Страница: 175 / 283

4.3 HDD

4 Replacement Procedures

Satellite M40/M45, TECRA A4, dynabook V x/4

Maintenance Manual

4-27

Installing the HDD

Install the HDD according to the following procedures and Figures 4-12, 4-13 and 4-14.

CAUTION

: To avoid damage, always hold the HDD only by its sides.

Attach the HDD chassis and connector to the HDD pack.

Secure the HDD and its chassis with the two M3x4 black flat-head screws with M3x4
white head screws.

CAUTION

: When installing the HDD pack into the computer, do not press the center of

the HDD pack to prevent the HDD bracket from being distorted. Always hold the HDD
pack by its sides.

Install the HDD pack into the correct position in the computer. Connect the HDD pack to
the computer, holding the HDD pack by its sides.

Insert the HDD pack.

Secure the HDD cover with two M2.5x5 black flat-head screws.

Содержание SATELLITE M40 Series




























































































































































































































































































Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды