Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 188

Страница: 188 / 283

4.9 Display Assembly

4 Replacement Procedures

Satellite M40/M45, TECRA A4, dynabook V x/4 Maintenance Manual

4-39

Disassembling the ODD Drive

NOTE:

Do not disassemble the ODD drive when it is working normally. Disassemble or

replace the ODD drive only if it failed.

Disassemble the ODD drive according to the following procedures and Figures 4-26.

Remove the two

M2x3 white flat-head screws.

Remove

the

bracket.

ODD bay module

M2x3
white flat-head screw

Breaket

Figure 4-26 Removing the bracket from the ODD drive

Assembling the ODD Drive

Assemble the ODD drive according to the following procedures and Figures 4-26.

Secure the bracket with the two M2x3 white flat-head screws.

Содержание SATELLITE M40 Series




























































































































































































































































































Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды