Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 39

Страница: 39 / 283

1.9 Power Supply

1 Hardware Overview

Satellite M40/M45 TECRA A4 dynabook Vx/4 Maintenance Manual

1.9 Power Supply

The power supply unit provides many different voltages for the system board and performs the following
functions:

Power input monitor

Checks whether the DC power supply (AC adapter) is connected to the computer.

Checks whether the battery pack is connected to the computer.

Monitors the DC power supply input voltage (AC Adapter output voltage).

Power supply's internal control

Turns on and off the battery pack charging power supply.

Issues a charging current instruction to the PWM control IC of the battery pack charging power

supply.

Controls the supply of DC power supply input (AC Adapter output) to the power supply unit.

Controls the supply of power to the system block (load/logic circuit side).

Controls forced shutdown if the power supply malfunctions.

Logic circuit control

Instructs the gate array to enable/disable tuning the power on.

Controls power-on/off operation.

Status display

Turns on the Power LED (in Green or AMBER).

Battery indicator (in Green or AMBER).

External interface

Performs communication through the I2C bus (via the internal EC/KBC).

Transfers the power supply operation mode.

Output monitor

Monitors the voltage output to the system block (load/logic circuit side).

Monitors the voltage, over voltage, input/output current of the battery pack.

Monitors the internal temperature of the battery pack.

Monitors the supply voltage from the AC adapter.

Содержание SATELLITE M40 Series




























































































































































































































































































Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды