Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 283

Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 117

3.7 Storage

3 Diagnostic Programs

Satellite M40/M45 TECRA A4 Dynabook Vx/4 Maintenance

Manual

43

Check the HDD controller’s status, including HDD interrupt and unexpected
interrupt.

5.

Diagnostic Read/Write

This test item is a quick test to verify whether the HDD could be correctly
accessed and the user could specify the percentage in the below dialog.

Percent (1-100)

-- Specify the coverage rate in percentage of the total disk.

Time Limit(h):

Choose or Input the time (hour) of the defined range of the total

disk to be tested;

Time Limit(m):

Choose or Input the time (minute) of the defined range of the

total disk to be tested;

6.

SMART Test

SMART stands for Self-Monitoring, Analysis and Reporting Technology.
SMART test will compare the attribute values with the threshold value in the
HDD’s controller to confirm whe ther there is any failure in the HDD

Subtest 02 ODD

The ODD test runs on IDE CDROM/DVD-ROM & CD-RW. It will check the ODD

driver’s functionality and performance.

1.

Controller Test

Check the CDROM controller’s status.

2.

Data Transfer Rate

Check the data trans fer rate of the ODD drive. It will read data from the ODD disc
and calculate the data transfer rate. This test needs a data CD.

«
...
115
116
117
118
119
...
»

Содержание SATELLITE M40 Series




























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды