manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Поделиться
Скачать
Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 189

4 Replacement Procedures

 

4.8 ODD Bay Module

 

4-40

 

Satellite M40/M45, TECRA A4, dynabook V x/4 Maintenance Manual

 

4.9  Display Assembly 

Removing the Display Assembly 

CAUTION

:  Use care to avoid that the antenna cable for antenna is caught between the 

display assembly and computer. 

Remove the display assembly according to the following procedures and Figures 4-27, 4-28.  

1.

 

Turn the computer back to front and remove four M2.5x8 black flat-head screws. 

2.

 

Restore the normal computer placement and open the display panel. 

 

Figure 4-27 Removing the screws from the back of the compute 

3.

 

Disconnect the LCD/FL cable from CN1on the system board. 

4.

 

Remove two M2.5x5 black flat-head screws to secure the LCD module to top cover. 

5.

 

Remove the wireless antenna cables from the top cover. 

6.

 

Remove the display module.

Содержание SATELLITE M40 Series




























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды