manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Поделиться
Скачать
Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 176

4 Replacement Procedures

 

4.4 CPU Cooling Module

 

4-28

 

Satellite M40/M45, TECRA A4, dynabook V x/4 Maintenance Manual

 

4.4  Cooling Module 

CAUTION: 

When removing the cooling module, keep the following in mind:

 

The cooling module can become very hot during operation. Be sure to let it cool down 
before starting the repair work. 

 

Do not touch or give shock to the fan in the cooling module.

 

 

NOTE: 

The screws for Steps 2 and 3 cannot be removed, only loosened. 

Removing the Cooling Module 

Remove the cooling module according to the following procedures and Figures 4-15, 4-16.  

1.

 

Turn the computer upside down.  

2.

 

Release the CPU cover securing screw. 

3.

 

Remove the CPU cover. 

4.

 

Release the three screws on the cooling module using the numbered order shown to the 
screw. 

5.

 

Remove the cooling module. 

 

Figure 4-15 Removing the CPU cover 

Содержание SATELLITE M40 Series




























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды