Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 172

Страница: 172 / 283

4 Replacement Procedures

4.2 Wireless LAN Card

4-24

Satellite M40/M45, TECRA A4, dynabook V x/4 Maintenance Manual

Figure 4-11 Removing the wireless LAN card

Installing the Wireless LAN Card

Install the wireless LAN card according to the following procedures and Figures 4-10, 4-11.

Insert the wireless LAN card into the connector at angle of 45 degrees.

Tilt the wireless LAN card and fix it with the left and right stoppers.

Connect the two antenna cables with the tweezers.

Install the wireless LAN cover.

Securing the wireless LAN cover by LAN cover securing screw.

CAUTION

: Do not touch the connectors on the wireless LAN card and in the computer

with bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural
oils, etc. from your hands.

Содержание SATELLITE M40 Series




























































































































































































































































































Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды