Toshiba SATELLITE M40 Series Скачать руководство пользователя страница 174

Страница: 174 / 283

4 Replacement Procedures

4.3 HDD

4-26

Satellite M40/M45, TECRA A4, dynabook V x/4 Maintenance Manual

Figure 4-13 Removing the HDD pack

Remove the HDD pack by pulling the HDD tap attached to the HDD pack.

NOTE:

Do not disassemble the HDD pack when it is working normally. Disassemble or

replace the HDD pack only if it failed.

Place the HDD pack on a flat surface (such as a desk), and remove the two M3x4 black
flat-head screws with M3x4 white head screws.

Remove the HDD chassis.

Remove the HDD connector.

Figure 4-14 Removing the HDD chassis

CAUTION

: Do not apply pressure to the top or bottom of the drive.

Содержание SATELLITE M40 Series




























































































































































































































































































Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды

Toshiba SATELLITE M40 Series, Руководство по обслуживанию

Результаты поиска

Содержание SATELLITE M40 Series

Отзывы:

Бренды по названию

Популярные бренды