manualshive.com logo in svg

Toshiba GX9 ASD, Быстрый старт

Поделиться
Скачать
Toshiba GX9 ASD Скачать руководство пользователя страница 62

52

GX9 ASD Quick Start Guide

System Operation

Startup Wizard

The 

Startup Wizard

 launches upon the first power up of the system and assists with the initial 

configuration of the input power settings and the output parameters of the 

GX9

 

ASD

. The GX9 ASD may 

also be setup via communications, by directly accessing the individual parameters via the menu hierarchy, 
or using the 

Direct Access

 parameter numbers. 

See the section titled 

Default Setting Changes on pg. 53

 for more information on changing the parameter 

settings.

After the initial execution of the 

Startup Wizard

 at the first power up, the wizard may only be run by 

setting the following menu item to 

Yes

 — Program 

 Utilities 

 Display Parameters 

 

Display the 

startup wizard next power-up?

Upon the next power up, the system will launch to the 

Startup Wizard

. Once completed, the system will 

set the 

Display the startup wizard next power-up?

 

setting to 

No

 (for the next system power up) and 

normal startups will resume.

The 

Startup Wizard 

querys the user for the following information:

1.

The 

Voltage and Frequency Rating of the Motor

.

2.

The 

Upper Limit Frequency

.

3.

The 

Lower Limit Frequency

.

4.

Adjust 

Adjust Accel/Decel Automatically?

 (if 

Enabled

, continue from step #

7

).

5.

The 

Acceleration Time

.

6.

The 

Deceleration Time

.

7.

The 

Volts Per Hertz Setting

.

8.

The 

Motor Current Rating

.

9.

The 

Motor Capacity

.

10. The 

Command Source

.

11. The 

Frequency Command Source

.

12. The 

Display Units

 for current and voltage.

Click 

Exit

 to load the settings of the 

Startup Wizard

 into the ASD.

See the section titled 

Startup Wizard Requirements on pg. 54

 for additional information on the 

Startup 

Wizard

.

Operation 

(Local)

Note:

See 

Local|Remote Key on pg. 28

 

for information on 

Remote

 operation.

To turn the motor on, perform the following:

1.

Press the 

Mode

 key until the 

Frequency Command

 

screen is displayed.

2.

Press the 

Local/Remote

 key to enter the 

Local 

mode 

(green Local LED illuminates).

3.

Turn the 

Rotary Encoder 

clockwise until the  

Fre-

quency Command

 value is displayed in the 

Set

 field.

4.

Press the 

Run

 key and the motor runs at the 

Frequency Command

 value.

Note:

The speed of the motor may be changed while the motor is running by using the 

Rotary 

Encoder

 to change the 

Frequency Command 

value.

5.

Press the 

Stop|Reset

 key to stop the motor.

Содержание GX9 ASD





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды