manualshive.com logo in svg

Toshiba GX9 ASD, Быстрый старт

Поделиться
Скачать
Toshiba GX9 ASD Скачать руководство пользователя страница 64

54

GX9 ASD Installation and Operation Manual

Startup Wizard Requirements

The 

Startup Wizard

 assists the user with the initial configuration of the 

GX9 ASD

 by querying the user 

for information on the ASD control settings, motor ratings, and ASD display units. The GX9 ASD may 
also be setup by accessing each of the settings via the 

Program

 menu or by using the 

Direct Access 

Number

 of each parameter (see the 

GX9 ASD Installation and Operation Manual

 for specifics on each 

parameter).

Upon initial system power up, the 

Startup Wizard

 starts automatically and the Welcome screen is 

displayed. Click 

Next

 to continue with the 

Startup Wizard

 or click 

Exit 

to go to the 

Wizard Finished!

 

screen.

Running the Startup Wizard

Input the required information into the following screens to complete the 

Startup Wizard

.

1. Voltage and Frequency Rating of the Motor

Motors are designed and manufactured for operation 
within a specific voltage and frequency range. The 
voltage and frequency specifications for a given 
motor may be found on the nameplate of the motor.

Settings:

4 — 575V 60 Hz

2. Upper Limit Frequency

This parameter sets the highest frequency that the 
GX9 ASD will accept as a frequency command or 
frequency setpoint. The GX9 ASD may output 
frequencies greater than the 

Upper Limit 

Frequency

 (but, less than the Maximum Frequency) 

when operating in the 

PID Control

 mode, 

Torque 

Control

 mode, or the 

Vector Control

 mode 

(sensorless or feedback).

3. Lower Limit Frequency

This parameter sets the lowest frequency that the 
GX9 ASD will accept as a frequency command or 
frequency setpoint. The GX9 ASD will output 
frequencies lower than the 

Lower Limit Frequency

 

when accelerating to the lower limit or decelerating 
to a stop. Frequencies below the 

Lower Limit

 may 

also be output when operating in the 

PID Control

 

mode, 

Torque Control

 mode, or the 

Vector Control

 

mode (sensorless or feedback).

Содержание GX9 ASD





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды