Toshiba GX9 ASD Скачать руководство пользователя страница 23

Страница: 23 / 100

GX9 ASD Quick Start Guide

Connecting the ASD

Contact With 3-Phase Input/Output Terminals May Cause An Electrical Shock

Resulting In Injury Or Loss Of Life.

Refer to the section titled

Installation Precautions on pg. 4

and the section titled

Lead Length

Specifications on pg. 15

before attempting to connect the ASD and the motor to electrical power.

Power Connections

See

Figure 19 on pg 26

for a system I/O connectivity schematic.

R/L1

S/L2

, and

T/L3

are the 3-phase input supply terminals for the ASD.

U/T1

V/T2

, and

W/T3

are the output terminals of the ASD that connect to the motor.

Connect the input and output power lines of the ASD as shown in

Figure 4 on pg 14

An inductor (DCL) may be connected across the

and

PA/+

terminals to provide additional filtering.

When not used, a jumper must be connected across these terminals.

PA/+

and

are used for the DBR connection if using a braking resistor.

PC/-

is the negative terminal of the DC bus.

The

Charge Indicator LED

provides an indication that there is a harmful voltage level present. The

location of the

Charge Indicator LED

is shown in

Figure 3

Ensure that the

Charge Indicator LED

is off before coming into contact with any circuits or attempting

to perform any maintenance on the ASD.

Note:

The GX9610K is shown in figure 3 below. See the drawings of the system received for
the actual location of the Charge LED.

Figure 3. Typical GX9 ASD Charge Indicator LED.

DANGER

Charge LED

Содержание GX9 ASD





































































































Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды

Toshiba GX9 ASD, Быстрый старт

Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды