Toshiba GX9 ASD Скачать руководство пользователя страница 38

Страница: 38 / 100

GX9 ASD Quick Start Guide

EOI Remote Mounting

The EOI may be mounted remotely using the optional

ASD-MTG-KIT9

. Or if operating in a

NEMA 4

environment, the

ASD-EOI-N4-G9

is best suited for this application. Each kit contains all of the

hardware required to mount the EOI of the GX9 ASD remotely.

System operation and EOI operation while using the remotely-mounted EOI are the same as with the
ASD-mounted configuration.

See the section titled EOI Remote Mounting in the

GX9 ASD Installation & Operation Manual

for more

information on mounting the EOI remotely.

EOI Features

Figure 20. The GX9 ASD Electronic Operator Interface Features.

LED Screen

—

Displays the running frequency, active

Fault

, or active

Alarm

information.

Rotary Encoder

— Used to access the GX9 ASD menu selections, change the value of a displayed

parameter (while in edit mode), and perform the

Enter

key function. Turn the

Rotary Encoder

either

clockwise or counterclockwise to perform the

Down

functions of the displayed menu selection.

Press the

Rotary Encoder

to perform the

Enter

(select) function. Press while turning for times-ten

increment/decrement.

LCD Screen

— Displays configuration information, performance data (e.g., output frequency, bus

voltage, torque, etc.), diagnostic information, and

LED

screen information in expanded normal text.

Local|Remote Key

— Toggles the system to and from the

Local

and

Remote

modes. The

Local/

Remote

key

is disabled while the

Fault

screen is active. The

Local/Remote

key

LED is on when the

system is in the

Local

mode. The

Local

mode allows the

Command

and

Frequency

control functions to

be carried out via the

EOI

The

Remote

mode enables the

Command

and

Frequency

control functions to be carried out via the

Terminal Board

RS485

Communication Board

Pulse Input,

or the settings of

F003

F004

. The

(

F003

F004

)

selection may be made via Program



Fundamental



Standard Mode Selection



Command Mode

and

Frequency Mode 1

, respectively.

The availability of

Local

mode control (

Command

and

Frequency

control) may be disabled via Program



Utilities



Prohibition



Local/Remote Key Command Override

and

Local/Remote Key Frequency

Override

. The availability of the

Local

mode of operation may be reinstated by changing this setting or

performing a

Reset

(see

F007

LCD Screen

Rotary Encoder

Remote/Local

Mode

Key

Escape Key

Stop-Reset Key

Key (LED)

Run Key

(LED)

LED Screen

Remove the
Phillips screw first
to remove the
LED/LCD display
unit to activate the

Battery Backup

system.

LED/LCD Display Unit

Local|Remote
Key

Содержание GX9 ASD





































































































Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды

Toshiba GX9 ASD, Быстрый старт

Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды