manualshive.com logo in svg

Toshiba GX9 ASD, Быстрый старт

Поделиться
Скачать
Toshiba GX9 ASD Скачать руководство пользователя страница 5

Introduction

Congratulations on the purchase of the 

GX9 Adjustable Speed Drive

!

The 

GX9 Adjustable Speed Drive 

(ASD) is a solid-state AC drive that features Toshiba International 

Corporation’s (TIC) 

Virtual Linear Pump

 

Technology

 (VLP Technology) and 

Vector Control

 

algorithms. The 

Virtual Linear Pump

 

Technology

 and 

Vector Control

 algorithms provide easy setup, 

enhanced reliability, and precise control under the most demanding conditions, all while enabling the 
motors of the system to develop high starting torque and providing compensation for motor slip. The 
result is setup ease, smooth starts, and highly efficient operation.

The 

Virtual Linear Pump Technology

 algorithm was designed to remove the guess work that is 

normally associated with the setup of pumping systems. It allows for pump curve responses that are 
precise, linear, and consistent at any flow or pressure setting. Eliminating the normal concerns of the 
adverse effects of conventional pumping system control response curves, the 

Virtual Linear Pump 

Technology

 algorithm allows the system to adapt seamlessly and easily to peak load demands while 

maintaining the same degree of high performance output and reliability across the entire load range — 
all without any user intervention.

The 

GX9 ASD

 is a very powerful tool, yet surprisingly simple to operate. The user-friendly 

Electronic 

Operator Interface

 (EOI) of the GX9 ASD has an easy-to-read LCD screen and a high-intensity LED 

display. The EOI provides easy access to the many monitoring and programming features of the GX9 
ASD.

The 

GX9 ASD

 uses digitally-controlled pulse width modulation. The programmable functions may be 

accessed via the easy-to-use menu, via the 

Direct Access Numbers

, or using communications via a host 

PC. The ease of system access to the monitoring and control features combined with Toshiba’s high-
performance software, delivers unparalleled motor control precision and reliability.

This guide has been prepared to enable installers, users, and maintenance personnel to maximize the 
abilities of the 

GX9 ASD

. With this in mind, use this guide to develop a system familiarity before 

attempting to install or operate the device. This guide may also be used as a reference guide or for 
training.

Содержание GX9 ASD





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды