Toshiba GX9 ASD Скачать руководство пользователя страница 42

Страница: 42 / 100

GX9 ASD Quick Start Guide

EOI Command (RS232/RS485) Menu

The

Command (RS232/RS485)

menu is accessed by pressing

ESC

from the

Frequency Command

screen. The control settings of the

Command (RS232/RS485)

menu are effective for

EOI

control only.

The

Command (RS232/RS485)

menu provides quick access to the following menu parameters:

Direction

—

Forward

Reverse

Stop Pattern

— The

Decel Stop

Coast

Stop

settings

determines the method used to stop the motor

when using the

Stop|Reset

key of the

EOI

. The

Decel Stop

setting enables the

Dynamic Braking

system setup at

F304

or the

DC Injection Braking

system setup at

F250

F251

, and

F252

. The

Coast

Stop

setting allows the motor to stop at the rate allowed by the inertia of the load.

Note:

The

Stop Pattern

setting has no effect on the

Emergency Off

settings of

F603

V/f Group

— 1 of 4

V/f

profiles may be selected and run. Each

V/f

profile is comprised of 4 user

settings:

Base Frequency

Base Frequency Voltage

Manual Torque Boost

, and

Motor Overload

Protection

. Expanded descriptions of these parameters may be found in the section titled Direct

Access Parameter Information in the

GX9 ASD Installation & Operation Manual

Accel/Decel Group

— 1 of 4

Accel/Decel

profiles may be selected and run. Each of the

Accel/Decel

profiles is comprised of 3 user settings:

Acceleration

Deceleration

, and

Pattern

. Expanded

descriptions of these parameters may be found in the section titled Direct Access Parameter
Information in the

GX9 ASD Installation & Operation Manual

PID Control

— This feature enables or disables the

PID

feedback function.

Torque Limit Group

— This parameter is used to select 1 of 4 preset positive torque limits to apply

to the active motor (of a multiple motor configuration). The settings of profiles 1 – 4 may be setup at

F441

F444

F446

, and

F448

, respectively.

VLP Technology Control

— This feature enables or disables the

Virtual Linear Pump

function.

Содержание GX9 ASD





































































































Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды

Toshiba GX9 ASD, Быстрый старт

Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды