Toshiba GX9 ASD Скачать руководство пользователя страница 81

Страница: 81 / 100

GX9 ASD Quick Start Guide

OL1

ASD Overload

• Acceleration time is too short.

• DC Injection current is too high.

• Improper V/f setting.

• Motor running during restart.

• ASD or the motor is improperly matched to the application.

OL2

Motor Overload

• Improper V/f setting.

• Motor is locked.

• Continuous operation at low speed.

• Load requirement exceeds ability of the motor.

• Startup frequency setting adjustment required.

OLR

Dynamic Braking
Resistor Overload

• Deceleration time is too short.

• DBR setting adjustment required.

• Over-Voltage Stall setting adjustment required.

OP1

Over-Voltage During
Acceleration

• Motor running during restart.

OP2

Over-Voltage During
Deceleration

• Deceleration time is too short.

• DBR value is too high.

• DBR required (DBR setup required).

• Stall protection is disabled.

• 3-phase input voltage is out of specification.

• Input reactance required.

OP3

Over-Voltage During
Fixed Speed

• Load fluctuations.

• 3-Phase input voltage out of specification.

• DBR required (DBR setup required).

Over-Torque

• A torque requirement by the load in excess of the setting of

F616

F617

for

a time longer than the setting of

F618

• The ASD is improperly matched to the application.

• The load is obstructed.

SEAL

Virtual Linear Pump
Sealing Water Error

• Inadequate pump seal water.

• Loss of pump seal water.

UP1

Main Power



Under-Voltage

• Input 3-phase voltage is too low.

• Momentary power failure longer than the time setting of

F628

UP2

Control Power



Under-Voltage

• This fault is caused by an under-voltage condition at the 5, 15, or the 24 VDC

supply.

• 3-phase input voltage low.

LED Screen

LCD Screen

Possible Causes/Troubleshooting

Содержание GX9 ASD





































































































Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды

Toshiba GX9 ASD, Быстрый старт

Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды