Toshiba E-Studio167 Скачать руководство пользователя | Manualshive

Страница: 3 / 266

background image

GENERAL PRECAUTIONS REGARDING THE SERVICE FOR
e-STUDIO167/207/237

The installation and service should be done by a qualified service
technician.

1)

Transportation/Installation

-

When transporting/installing the equipment, remove the drawer, employ two persons and be sure
to hold the positions as shown in the figure.
The equipment is quite heavy and weighs approximately 32.5 kg (71.65 lb), therefore pay full
attention when handling it.

-

Be sure not to hold the movable parts or units when transporting the equipment.

-

Be sure to use a dedicated outlet with AC 110 V / 13.2 A, 115 V or 127 V / 12 A, 220-240 V or 240
V / 8 A for its power source.

-

The equipment must be grounded for safety.

-

Select a suitable place for installation. Avoid excessive heat, high humidity, dust, vibration and
direct sunlight.

-

Provide proper ventilation since the equipment emits a slight amount of ozone.

-

To insure adequate working space for the copying operation, keep a minimum clearance of 80
cm (32”) on the left, 80 cm (32”) on the right and 10 cm (4”) on the rear.

-

The equipment shall be installed near the socket outlet and shall be easily accessible.

-

Be sure to fix and plug in the power cable securely after the installation so that no one trips over
it.

2)

General Precautions at Service

-

Be sure to turn the power OFF and unplug the power cable during service (except for the service
should be done with the power turned ON).

-

Unplug the power cable and clean the area around the prongs of the plug and socket outlet once
a year or more. A fire may occur when dust lies on this area.

-

When the parts are disassembled, reassembly is the reverse of disassembly unless otherwise
noted in this manual or other related documents. Be careful not to install small parts such as
screws, washers, pins, E-rings, star washers in the wrong places.

-

Basically, the equipment should not be operated with any parts removed or disassembled.

-

The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband
since the ICs on it may be damaged due to static electricity.

Caution: Before using the wristband, unplug the power cable of the equipment and

make sure that there are no charged objects which are not insulated in the
vicinity.

«
1
2
3
4
5
...
»

Содержание E-Studio167











































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio167

Бренд: Canon Страницы: 11

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 12

PIXMA Pro9000 Mark II Series

Бренд: Canon Страницы: 4

Бренд: Unitech Страницы: 2

Бренд: Unimark Страницы: 38

WorkCentre 5325

Бренд: Xerox Страницы: 160

WorkCentre 5016

Бренд: Xerox Страницы: 2

WorkCentre 490cx

Бренд: Xerox Страницы: 258

WorkCentre 4260 Series

Бренд: Xerox Страницы: 210

WorkCentre 3550

Бренд: Xerox Страницы: 32

WorkCentre 3315DN

Бренд: Xerox Страницы: 191

WORKCENTER 5222

Бренд: Xerox Страницы: 28

VersaLink C71 Series

Бренд: Xerox Страницы: 247

VersaLink C7000

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 21

VersaLink B71 Series

Бренд: Xerox Страницы: 234

WorkCentre 6505

Бренд: Xerox Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды