Toshiba E-Studio167 Скачать руководство пользователя

Страница: 85 / 266

e-STUDIO167/207/237

CONTROL PANEL

5 - 3

5.2.2

Message

No.

Message

Condition of machine

Notes

Wait warming up

Being warmed up
•

Displayed after the main switch is
turned ON up until the machine
becomes ready for copying

READY

Standby for copying
•

The machine is ready for copying
and operator's instructions on copy-
ing conditions can be input

•

Returns to the default condition if
no key is pressed for the setting
time of auto clear timer

•

Copy quantity indicator shows
"1"When a digital key is pressed,
that number indicates the set quan-
tity

•

The set quantity can be cleared to
"1" by pressing the CLEAR/ STOP
key

•

Bypass copying is possible

COPYING

Now copying
•

Displayed by pressing the START
key

•

Copy quantity indicator becomes
"ex. 3

3" and copying is

completed

•

After completion of copying, the
copy quantity indicator returns to
the initially set number

Saving energy

Energy saver conditions

•

Reset by pressing the any key
except the ENERGY SAVER key

Select original size

Platen sort copying standby state

•

When using original cover

Timer off
•

No message is displayed in the dis-
play panel

Cassette * empty

Indication of lack of paper
•

Indicates when there is no paper in
cassette

•

Bypass copying is possible

•

Supply paper to the selected cas-
sette

•

Select another cassette

Toner empty

Indication of lack of toner
•

The toner in the toner cartridge
becomes empty

•

When this message is displayed, it
is not possible to copy

•

Reset after the toner is supplied
and the front cover is closed

Misfeed in bypass

Bypass paper jamming (SFB)
•

Paper jams at the bypass tray

The machine returns to normal condi-
tions automatically when the paper out
is pulled from the bypass tray

Misfeed in copier
(Copier machine)

Paper jammed in the machine

Remove the paper jammed in the
copier by following the messages

Misfeed in doc. Feeder
(ADF)

Original jammed
•

An original is jammed in the ADF

Open the ADF jam access cover and
the ADF unit, and remove the jammed
original

Misfeed in duplexer
(ADU)

Paper jammed in the ADU

Remove the paper jammed in the
copier by following the message

Call for service

Some part of the mechanism, motors,
switches or sensors is abnormal

Turn OFF the machine, remove the
cause of the fault and turn the machine
back ON

Time for maintenance

Indication of PM cycle
•

Displayed when it is time for pre-
ventive maintenance and inspection

•

Capable of copying

Maintenance and inspection by a quali-
fied service technician

Содержание E-Studio167
























































































































































































































































Результаты поиска

Содержание E-Studio167

Отзывы:

Похожие инструкции для E-Studio167

Бренды по названию

Популярные бренды

Toshiba E-Studio167, Руководство по обслуживанию

Результаты поиска

Содержание E-Studio167

Отзывы:

Похожие инструкции для E-Studio167

Бренды по названию

Популярные бренды