manualshive.com logo in svg

Toshiba E-Studio167, Руководство по обслуживанию

Операторская инструкция к Toshiba E-Studio167 доступна для бесплатного скачивания на manualshive.com. Обеспечьте правильное использование устройства, скачав руководство, которое содержит все необходимые инструкции. Получите доступ к полной информации о продукте, скачав мануал с нашего сайта.

Поделиться
Скачать
background image

© February 2007 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

CONTENTS

3

12.2 Construction....................................................................................................................... 12-2
12.3 Functions ........................................................................................................................... 12-3

12.3.1 Function of each unit .............................................................................................. 12-3
12.3.2 Functions of the toner cartridge PC board (CTRG) ................................................ 12-4
12.3.3 Recovered toner supply mechanism ...................................................................... 12-6

12.4 Toner Motor Control Circuit ............................................................................................... 12-7
12.5 Auto-Toner Circuit.............................................................................................................. 12-8

12.5.1 General description ................................................................................................ 12-8
12.5.2 Function of auto-toner sensor ................................................................................ 12-9

12.6 Disassembly and Replacement ....................................................................................... 12-11

13. FUSER / EXIT UNIT .................................................................................................... 13-1

13.1 General Description ........................................................................................................... 13-1
13.2 Configurations.................................................................................................................... 13-2
13.3 Functions ........................................................................................................................... 13-3
13.4 Operation ........................................................................................................................... 13-5
13.5 Fuser Unit Control Circuit .................................................................................................. 13-6

13.5.1 Configuration .......................................................................................................... 13-6
13.5.2 Temperature detection section ............................................................................... 13-7

13.6 Disassembly and Replacement ....................................................................................... 13-12

14. AUTOMATIC DUPLEXING UNIT (ADU) (OPTION: MD-0103) .................................. 14-1

14.1 General Description ........................................................................................................... 14-1

14.1.1 Specifications of MD-0103 ..................................................................................... 14-2

14.2 Construction....................................................................................................................... 14-3
14.3 Functions ........................................................................................................................... 14-4
14.4 Drive of ADU...................................................................................................................... 14-5
14.5  Description of Operation ................................................................................................... 14-6
14.6 Flow Chart ....................................................................................................................... 14-11
14.7 Disassembly and Replacement ....................................................................................... 14-12

15. POWER SUPPLY UNIT .............................................................................................. 15-1

15.1 Construction....................................................................................................................... 15-1
15.2 Operation of DC Output Circuit.......................................................................................... 15-2
15.3 Output Channel ................................................................................................................. 15-3
15.4 Fuse................................................................................................................................... 15-4
15.5 Configuration of Power Supply Unit................................................................................... 15-5
15.6 Power Supply Sequence ................................................................................................... 15-6
15.7 AC Wire Harness ............................................................................................................... 15-7

16. PC BOARDS ............................................................................................................... 16-1

Содержание E-Studio167











































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio167

Xerox 4450 Forms Creation Manual preview
4450
Бренд: Xerox Страницы: 108
Oki OKIPAGE 8z Technical Features preview
OKIPAGE 8z
Бренд: Oki Страницы: 2
Oki OKIPAGE 8c Plus User Manual preview
OKIPAGE 8c Plus
Бренд: Oki Страницы: 48
Oki OKIPAGE 6e Maintenance Manual preview
OKIPAGE 6e
Бренд: Oki Страницы: 257
Oki OKIPAGE 14i Technical Reference preview
OKIPAGE 14i
Бренд: Oki Страницы: 113
Oki OKIPAGE 14e Setup Manual preview
OKIPAGE 14e
Бренд: Oki Страницы: 26
Oki OKIPAGE 14e Service Manual preview
OKIPAGE 14e
Бренд: Oki Страницы: 183
Oki MPS730b Material Safety Data Sheet preview
MPS730b
Бренд: Oki Страницы: 36
Oki MPS730b User Manual preview
MPS730b
Бренд: Oki Страницы: 136
Oki MPS710c Handy Reference preview
MPS710c
Бренд: Oki Страницы: 66
Oki MPS711c Manual De L'Utilisateur preview
MPS711c
Бренд: Oki Страницы: 123
Oki MPS711c User Manual preview
MPS711c
Бренд: Oki Страницы: 109
Oki Microline 520 User Manual preview
Microline 520
Бренд: Oki Страницы: 68
Oki Microline 3320 Maintenance Manual preview
Microline 3320
Бренд: Oki Страницы: 12
Oki OKIPOS X400 Manual De L'Utilisateur preview
OKIPOS X400
Бренд: Oki Страницы: 22
Oki OKIPOS X400 Guía Del Usuario preview
OKIPOS X400
Бренд: Oki Страницы: 22
Oki OKIPOS X400 User Manual preview
OKIPOS X400
Бренд: Oki Страницы: 27
Oki OKIPAGE 12i Series Maintenance Manual preview
OKIPAGE 12i Series
Бренд: Oki Страницы: 210

Бренды по названию

Популярные бренды

Загрузить еще бренды