manualshive.com logo in svg

Toshiba E-Studio167, Руководство по обслуживанию

Операторская инструкция к Toshiba E-Studio167 доступна для бесплатного скачивания на manualshive.com. Обеспечьте правильное использование устройства, скачав руководство, которое содержит все необходимые инструкции. Получите доступ к полной информации о продукте, скачав мануал с нашего сайта.

Поделиться
Скачать
background image

13

© February 2007 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

FUSER / EXIT UNIT

13 - 3

13.3 Functions

1) Pressure roller

The pressure roller is a sponge roller which assures the nip amount of the fuser roller. The pressure 
from the spring presses the paper onto the fuser roller to fuse toner onto the paper efficiently.

2) Exit sensor (S5)

The exit sensor detects if the leading or trailing edge of the paper is passing through the pressure 
roller and the fuser roller. This sensor is used for the detection of paper jams in the fuser/exit unit as 
well.

3) Fuser roller

The fuser roller applies heat onto the paper and is heated by the heater lamps installed inside of the 
fuser roller. The heat from this roller fuses toner onto the paper. The fuser roller in this equipment is 
a thin roller which enhances heat conduction, and thus the warming-up time is shortened.

4) Heater lamp (LAMP1/LAMP2)

The heater lamps are halogen lamps to apply heat to the fuser roller. The fuser unit in this equip-
ment has 2 heater lamps (564W+564W) with different functions each other. One has a coil wound 
up on its center and this part generates heat. The other one has coils wound up on its both ends and 
these parts generate heat. The one has a coil on its center is called the center heater lamp (LAMP1) 
and the one has coils on its both ends is called the side heater lamp (LAMP2). 
The heater lamps are fixed on the inside of the fuser roller to heat it up. The heater lamps do not 
rotate even when the fuser roller is rotating.

5) Sensor thermistor (THMS1) / Side thermistor (THMS2)

This thermistor detects the temperature of the fuser roller to maintain it in a certain temperature 
range (actually around 170°C) between the lower limit causing the poor fusing and the upper limit 
causing the high temperature offsetting. When the temperature of the fuser roller is lower than the 
preset temperature, it turns ON the power supply to the heater lamps, and when it is higher than the 
preset temperature, it cuts off the supply.
The center thermistor (THMS1) detects the temperature of the center part of the fuser roller, and the 
side thermistor (THMS2) detects the temperature of one side of fuser roller and control the both 
sides.

6) Edge thermistor (THMS3)

Both the ends of the fuser roller may be overheated without heat absorption by the paper since it 
does not pass through this area. The edge thermistor (THMS3) detects any temperature abnormal-
ity of this area caused by overheating of the fuser roller. Therefore this thermistor is not used for 
temperature control of the fuser roller.

7) Fuser thermostat (THMO1)

The fuser thermostat (THMO1) cuts off the power supply to the heater lamps (LAMP1/LAMP2) by 
opening itself if the fuser roller becomes abnormally hot as a result of the problem such as ther-
mistor malfunction. The fuser thermostat (THMO1) for this equipment is used to prevent abnormal 
operation. When the fuser thermostat (THMO1) detects any abnormality, it must be replaced as well 
as the other damaged parts in the fuser unit.

8) Separation finger

Five separation fingers are installed above the fuser roller, in order to separate paper adhering to 
each roller.

9) Exit roller

The exit roller, which transports the paper to the inner tray, is driven by the main motor (M3). It is 
driven by the exit motor (M7) when the ADU (optional) is installed.

Содержание E-Studio167











































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio167

BadgePass NXT5000 Quick Start Manual preview
NXT5000
Бренд: BadgePass Страницы: 2
Xerox AS/400 Installation And Setup Manual preview
AS/400
Бренд: Xerox Страницы: 23
IBM 6400 Series Operator'S Manual preview
6400 Series
Бренд: IBM Страницы: 113
IBM 6400 Series Owner'S Manual preview
6400 Series
Бренд: IBM Страницы: 16
IBM 6400 Series User Manual preview
6400 Series
Бренд: IBM Страницы: 214
Xerox Phaser 6120 Service Manual preview
Phaser 6120
Бренд: Xerox Страницы: 15
Xerox Phaser 6120 Voluntary Product Accessibility Template preview
Phaser 6120
Бренд: Xerox Страницы: 9
Xerox DocuPrint 180 NPS Series Installation Planning Manual preview
DocuPrint 180 NPS Series
Бренд: Xerox Страницы: 172
Xerox Phaser 4500 Voluntary Product Accessibility Template preview
Phaser 4500
Бренд: Xerox Страницы: 11
Xerox Phaser 7750 Quick Reference Manual preview
Phaser 7750
Бренд: Xerox Страницы: 8
Xerox Phaser 7300 Features Manual preview
Phaser 7300
Бренд: Xerox Страницы: 40
Xerox ColorQube 8700 Reference Manual preview
ColorQube 8700
Бренд: Xerox Страницы: 28
Xerox Color C75 Press User Manual preview
Color C75 Press
Бренд: Xerox Страницы: 340
Xerox EC8036 User Manual preview
EC8036
Бренд: Xerox Страницы: 370
Xerox DocuPrint N3225 User Manual preview
DocuPrint N3225
Бренд: Xerox Страницы: 169
Xerox D110 Specification preview
D110
Бренд: Xerox Страницы: 8
Xerox DocuPrint 65 Quick Start Manual preview
DocuPrint 65
Бренд: Xerox Страницы: 16
Xerox Phaser 7400 Setup Manual preview
Phaser 7400
Бренд: Xerox Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды