manualshive.com logo in svg

Toshiba E-Studio167, Руководство по обслуживанию

Операторская инструкция к Toshiba E-Studio167 доступна для бесплатного скачивания на manualshive.com. Обеспечьте правильное использование устройства, скачав руководство, которое содержит все необходимые инструкции. Получите доступ к полной информации о продукте, скачав мануал с нашего сайта.

Поделиться
Скачать
background image

e-STUDIO167/207/237

© February 2007 TOSHIBA TEC CORPORATION All rights reserved

DEVELOPMENT SYSTEM

12 - 4

12.3.2

Functions of the toner cartridge PC board (CTRG)

The toner cartridge in this equipment mounts the toner cartridge PC board (CTRG). An IC chip is 
embedded in this board, and the data identifying the recommended TOSHIBA toner cartridge and 
thresholds to determine if the cartridge is nearly empty are written in this chip. 
To measure the amount of toner remaining in the cartridge, when the value of counter for period of 
toner cartridge rotation time (08-1410) is updated, this equipment writes the updated value into the 
toner cartridge PC board (CTRG).

These data written in the toner cartridge PC board (CTRG) enable the functions below, and accordingly 
this equipment operates as shown below. Data reading is performed every time the power of this equip-
ment is turned ON and the front cover is closed.

[Data read by the toner cartridge PC board (CTRG)]
•

Data to identify recommended TOSHIBA toner cartridges

•

Thresholds to determine if the toner cartridge is nearly empty

•

Value of counter for period of toner cartridge rotation time

[Functions]
•

Cartridge detecting function
This function checks whether the toner cartridge is inserted correctly or not, and whether the recom-
mended toner cartridge is used or not. 

•

Toner remaining check function
This function notifies the user of the near-empty status of toner. Normally, the message “Toner is 
low” is displayed when the toner is running out, and “Toner empty” when the toner cartridge is 
empty.

•

Toner remaining check notification function
Upon detecting the near-empty status of toner, this function automatically notifies your service rep-
resentative.

[Operations]

A sign of the status that the toner cartridge is nearly empty (= the behavior of the toner lamp) appears 
when the value of counter for period of toner cartridge rotation time has exceeded the thresholds previ-
ously written in the toner cartridge PC board (CTRG). When a used cartridge refilled with new toner is 
used, that is the value of counter for period of toner cartridge rotation time in the toner cartridge PC 
board (CTRG) had already exceeded the threshold to determine the near-empty status of the toner at 
this moment, the sign of the near-empty status appears immediately after the installation of this car-
tridge. When a non-recommended toner cartridge is used, the toner lamp is lit by the cartridge detecting 
function because its data cannot be read out.
The toner near-empty status threshold setting (08-971) is provided to adjust the timing for displaying 
the toner near-empty status as follows.

Toner cartridge

Recommended cartridge

Recommended cartridge 

refilled with new toner

Non-recommended cartridge

Cartridge detecting 
function

Enabled
“Toner not recognized” is 
displayed when no cartridge 
is installed.

Enabled
“Toner not recognized” is 
displayed when no car-
tridge is installed.

Disabled
“Toner not recognized” is dis-
played even when the car-
tridge is installed. 

Toner remaining 
check function

Enabled
“Toner is low” is displayed 
when the cartridge is nearly 
empty.

Disabled
“Toner is low” is displayed 
even when a new cartridge 
is installed.

Disabled
This function does not oper-
ate.

Toner remaining 
check notification 
function

Enabled

Disabled

Disabled

Содержание E-Studio167











































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio167

Canon iR3245 Troubleshooting Manual preview
iR3245
Бренд: Canon Страницы: 300
Canon iR3245 Network Manual preview
iR3245
Бренд: Canon Страницы: 288
Canon iR3245 User Manual preview
iR3245
Бренд: Canon Страницы: 58
Canon iR1510 Quick Start Manual preview
iR1510
Бренд: Canon Страницы: 30
Xerox DC240 - DocuColor 240 Color Laser Quick Start Manual preview
DC240 - DocuColor 240 Color Laser
Бренд: Xerox Страницы: 2
Xante ColourLaser series guide Quick Reference Manual preview
ColourLaser series guide
Бренд: Xante Страницы: 31
Xante AW 1200 Quick Reference Manual preview
AW 1200
Бренд: Xante Страницы: 31
Xante Accel-a-Writer 812 Maintenance Manual preview
Accel-a-Writer 812
Бренд: Xante Страницы: 12
Xante Ilumina Repacking And Shipping Manual preview
Ilumina
Бренд: Xante Страницы: 6
Nehoc TCA3-SP User Manual – Operating Manual preview
TCA3-SP
Бренд: Nehoc Страницы: 9
Oki MC561 Maintenance Manual preview
MC561
Бренд: Oki Страницы: 276
Brightek U04 Quick Install Manual preview
U04
Бренд: Brightek Страницы: 8
Lexmark MS310d Quick Refence Manual preview
MS310d
Бренд: Lexmark Страницы: 79
Oki ES8473 Maintenance Manual preview
ES8473
Бренд: Oki Страницы: 271
GRAPHTEC SignJet JS310 Series Setup Manual preview
SignJet JS310 Series
Бренд: GRAPHTEC Страницы: 83
Ricoh RN-MF1 Service Manual preview
RN-MF1
Бренд: Ricoh Страницы: 162
Kyocera ECOSYS P8060cdn Quick Manual preview
ECOSYS P8060cdn
Бренд: Kyocera Страницы: 20
Xerox 490 DC/ST User Manual preview
490 DC/ST
Бренд: Xerox Страницы: 85

Бренды по названию

Популярные бренды

Загрузить еще бренды