Toshiba E-Studio167 страница 99 Скачать руководство пользователя

Страница: 99 / 266

e-STUDIO167/207/237

SCANNER

6 - 7

Description of input signal

Clock input

SCNCLK

Input

The scan motor is rotated by inputting the pulses (CLK).
*

Internal circuit of the motor driver works when the first
pulse of the input becomes ON.

The maximum input clock is 9000 PPS.

Motor rotation direction setting

SCNDIR

Input

The direction of the motor rotation is determined by setting
the level of the signal.
“H”: Clockwise direction
“L”: Counterclockwise direction
*

The rotation direction within 7 µsec. before the first
pulse of the CLK comes should not be changed ON
and after the last pulse goes OFF.

Cutting off of the drive output

SCNEN

Input

Forcibly turn ON/OFF the excitation drive.
“H”: Normal operation (Excited)
“L”: Excitation drive is forcibly shut off (Not excited)

Excitation mode Setting-1

SCNMD0

Input

Sets the excitation mode.
*

The setting should not be changed within 7µsec. after
the first pulse of the CLK comes ON.

Resetting

SCANRST

Input

Resets the whole system.
“L” (10 µsec. or more): Internal circuit of the driver is ini-
tialized.
*

The motor drive circuit is automatically reset when the
power is turned ON.

Voltage to set value for the
motor current

SCNNVR

Input

Sets the reference current value for the constant current
detection.
Motor wire current value can be set in the range of 0 to 2.0
(A)/phase by applying the analog voltage of 0 to 5 (V).

Содержание E-Studio167
























































































































































































































































Результаты поиска

Содержание E-Studio167

Отзывы:

Похожие инструкции для E-Studio167

Бренды по названию

Популярные бренды

Toshiba E-Studio167, Руководство по обслуживанию

Результаты поиска

Содержание E-Studio167

Отзывы:

Похожие инструкции для E-Studio167

Бренды по названию

Популярные бренды