Toshiba E-Studio167 страница 198 Скачать руководство пользователя | Manualshive

Страница: 198 / 266

background image

e-STUDIO167/207/237

© February 2007 TOSHIBA TEC CORPORATION All rights reserved

DEVELOPMENT SYSTEM

12 - 6

12.3.3

Recovered toner supply mechanism

The toner scraped off by the drum cleaning blade is transported by the toner recovery auger and the
toner recycling auger to be recycled, and then returned into the developer unit. Then the recovered
toner in the developer unit is mixed by the developer material using the mixer-3. The mixer-3 is
mounted exclusively for the recovered toner to mix it in a sufficient period of time. On the other hand,
the (fresh) toner transported from the toner cartridge into the developer unit is mixed by the mixer-2.
Then the (fresh) toner and the recovered toner are mixed together and further transported to the mixer-
1. They are further mixed by the mixer-1 and transported to the developer sleeve.

Fig. 12-2

Drum cleaner

Mixer-1

Mixer-2

Toner recycling auger

Fresh toner
Recovered toner

Toner cartridge

Mixer-3

Toner recovery auger

«
...
196
197
198
199
200
...
»

Содержание E-Studio167











































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio167

Бренд: Olivetti Страницы: 2

Бренд: Olivetti Страницы: 109

Бренд: Olivetti Страницы: 111

Бренд: Olivetti Страницы: 8

Бренд: Xerox Страницы: 16

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 2

Бренд: Canon Страницы: 4

Бренд: Primera Страницы: 2

Бренд: TP Страницы: 10

apeosport-v c5585

Бренд: Fuji Xerox Страницы: 493

Бренд: Intermec Страницы: 2

Бренд: Ricoh Страницы: 2

VarioLink 2650cp

Бренд: Oce Страницы: 2

Бренд: Printekmobile Страницы: 2

Бренд: Canon Страницы: 76

Бренд: Xerox Страницы: 34

Бренд: DataCard Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды