Toshiba E-Studio167 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 266

background image

e-STUDIO167/207/237

© February 2007 TOSHIBA TEC CORPORATION All rights reserved

LASER OPTICAL UNIT

8 - 2

8.2

Structure

1) Laser emission Unit

This unit consists of the laser diode, finite focus lens, aperture and cylinder lens.
-

Laser diode
This laser diode features low droop, small laser variation and low threshold current.
Aperture determines the shape of the laser beam at laser emission position of the primary scan-
ning and secondary scanning.
Laser diode radiates the laser beams responding to the laser emission control (ON/OFF) signals
from the laser driving PC board (LDR). Laser beams which passed through the finite focus lens
are focused on the drum surface.

-

Laser precautions
A laser diode is used for this equipment and radiates an invisible laser beam.
Since it is not visible, be extremely careful when handling the laser optical unit components, per-
forming operations or adjusting the laser beam. Also never perform the procedure with other than
the specified manuals because you could be exposed to the laser radiation.
The laser optical unit is completely sealed with a protective cover. As long as only the operations
of specified manuals are performed, the laser beam is not leaked and you are in no danger of
being exposed to laser radiation.
The following cautionary label for the laser is attached to the front right cover (inside of the front
cover).

Fig. 8-3

Laser optical unit (1 beam)

Laser emission unit

Laser diode

Wavelength: Approx.785 nm
Output power rating: 5 mW

Fine focus lens

Aperture (Slit)

Cylinder lens

Laser driving PC board (LDR)

Polygonal motor unit

Polygonal motor (M4)

Polygonal mirror

6 planes

f

#

lens-1

f

#

lens-2

H-Sync returning mirror

Slit glass

H-sync signal detection PC board
(SNS)

«
...
124
125
126
127
128
...
»

Содержание E-Studio167











































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio167

Бренд: Unimark Страницы: 38

Бренд: GE Страницы: 16

Saddle Finisher-AF2

Бренд: Canon Страницы: 244

Бренд: Savin Страницы: 160

Бренд: Oce Страницы: 340

Бренд: Muratec Страницы: 112

Бренд: Xerox Страницы: 8

Бренд: Oki Страницы: 32

bizhub press c1060

Бренд: Konica Minolta Страницы: 159

DocuCentre-VI C2264

Бренд: Fuji Xerox Страницы: 129

Бренд: Pantum Страницы: 155

ColourLaser 21 Series

Бренд: Xante Страницы: 32

Бренд: DURACARD Страницы: 31

Бренд: Wang Страницы: 39

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 36

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 115

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды