Toro LX Lawn Tractor Скачать руководство пользователя страница 98

Страница: 98 / 236

CHASSIS

3-84

LX Lawn Tractor Service Manual

Fig 323

PICT-7221

Before making a neutral adjustment, the transmission

must be warmed up for at least 10 minutes.

1. Loosen the bolt and washer retaining the right side

wheel to the right side axle (Fig. 323).

Neutral Adjustment - Hydrostatic
Models

Fig 325

PICT-7599

4. Locate the neutral adjusting puck and loosen the

Allen head bolt. If it’s diffi cult to loosen, heat the
aluminum housing near the bolt with a propane torch
(Fig. 325).

Fig 324

PICT-7597

2. Raise and support the right rear end of the tractor to

permit removing the right rear tire. Make sure the left
rear tire stays on the ground.

3. Remove the bolt, washer and wheel assembly from

the right axle (Fig. 324).

A. Adjusting

puck

Содержание LX Lawn Tractor













































































































































































































































Результаты поиска

Содержание LX Lawn Tractor

Отзывы:

Бренды по названию

Популярные бренды

Toro LX Lawn Tractor, Руководство по обслуживанию

Результаты поиска

Содержание LX Lawn Tractor

Отзывы:

Бренды по названию

Популярные бренды