manualshive.com logo in svg

Toro LX Lawn Tractor, Руководство по обслуживанию

Поделиться
Скачать
Toro LX Lawn Tractor Скачать руководство пользователя страница 230

MOWER DECK

7-76

 

LX Lawn Tractor Service Manual

7

2.  Slide the cutting deck (from the right side) under-

neath the tractor (Fig. 839).

4.  Place blocks under the rear of the mower deck to 

raise it up.

5.  Lower the lift lever to the lowest height-of-cut setting 

(Fig. 841).

 

Fig 839

 PICT-9765

 

Fig 841

 PICT-9768

3.  Slide the cutting deck toward the front of the tractor 

allowing the hooks on the deck to hook onto the 
deck stabilizer rod (Fig. 840).

Note: Ensure the fl anges on the stabilizer rod are on 

the inside of the hooks on the deck.

 

Fig 840

 PICT-9771

50” Mower Deck Installation

1.  Raise the lift lever to the highest height-of-cut setting 

(Fig. 838).

 

Fig 838

 PICT-9766

Содержание LX Lawn Tractor













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды